GP60-005R-LFR thru gp60-10r-lfr page: 1 frontier electronics corp. 667 e. cochran street, simi valley, ca 93065 tel: (805) 522-9998 fax: (805) 522-9989 e-mail: frontiersales@frontierusa.com web: http://www.frontierusa.com 6a general purpose plastic rectifier GP60-005R-LFR thru gp60-10r-lfr features z high current lead mounted z diffused junction z high surge capability z low forward voltage drop z completely insulated case z uniform molded body z the plastic material carries u/l recognition 94v-0 z high temperature soldering guaranteed: 260c/10s /0.375?, (9.5mm) lead length/5 lbs. (2.3kg) tension z bevel round chip, avalanche operation z rohs mechanical data z case: molded plastic, p6, dimensions in inches and (millimeters) z terminal: axial leads, solderable per mil-std-202, method 208 z polarity: color band denotes cathode z mounting position: any z weight : 2.1 grams maximum ratings and electrical characteristics ratings at 25 c ambient temperature unless otherwise specified single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% ratings symbol gp60-005r -lfr gp60-01r -lfr gp60-02r -lfr gp60-04r -lfr gp60-06r -lfr gp60-08r -lfr gp60-10r -lfr units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current 0.375?(9.5mm) lead length at ta=55c i o 6.0 a peak forward surge current, 8.3ms single half sine-wave superimposed on rated load i fsm 400 a typical junction capacitance (note 1) c j 150 pf typical thermal resistance (note 2) r ja 10 c /w storage temperature range t stg - 55 to + 175 c operating temperature range t op - 55 to + 175 c electrical characteristics (a t t a =25 c unless otherwise noted) characteristics symbol gp60-005r -lfr gp60-01r -lfr gp60-02r -lfr gp60-04r -lfr gp60-06r -lfr gp60-08r -lfr gp60-10r -lfr units maximum forward voltage at i o dc v f 1.0 v maximum reverse current at 25 i r 5 a maximum reverse current at100 i r 50 a note: 1. measured at 1mhz and applied reverse voltage of 4.0 volts 2. both leads attached to heat sink 70701t(mm) copper plate at lead length 5mm .360(9.1) .340 ( 8.6 ) .052(1.3) .048(1.2) .360(9.1) .340(8.6) 1.0(25.4) min 1.0(25.4) min
GP60-005R-LFR thru gp60-10r-lfr page: 2 ratings and characteristic curve GP60-005R-LFR thru gp60-10r-lfr fig.4-typical reverse characteristics 100 10 1.0 0.1 .01 instantaneous forward current amperes 20 40 60 80 100 120 percent of rated peak reverse voltage t j =25 t j =100 fig.3-typical instantaneous forward characteristic 1000 100 10 1.0 0.1 instantaneous forward current microamperes .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 instantaneous forward voltage volts t j =25 pulse width=300us 1% duty cycle fig.5-maximum non-repetitive peak forward surge current 600 500 400 300 200 100 0 peak forward surge current amperes 1 10 100 t j =25 t j =150 8.3 ms single half sine-wave jedec method number of cycles at 60 h z 0 20 40 60 80 100 120 140 160 25 20 15 10 5 average forward current amperes fig.2-maximum forward current derating curve l=.625 (15.8mm) l=.375 ( 9.5mm ) l=.125 ( 3.18mm ) l=.25 (6.35mm) resistive or inductive load 60 h z both leads attached to heat sinks with lengths as shown lead temperature fig.6-typical transient thermal impedance transient thermal impedance, o c / watt 100 10 1 0.1 0.01 0.1 1 10 100 t, pulse duration, sec. fig.1-maximum forward current derating current 0 20 40 60 80 100 120 140 160 180 6.0 5.0 4.0 3.0 2.0 1.0 0 average forward current amperes pc board standard pc board mounting 60 h z resistive or inductive loads ground plane 1 x 1 copper surface area recommended pc board mounting ambient temperature
|
